![]() There are also ways that dabs can be consumed without a rig. Why not add some terp pearls and quartz inserts into the mix for good measure? You’ll also need either a torch or an eNail for heating the nail. You can get started by purchasing a dab rig, a quartz nail, a dabber to break apart the shatter, and a carb cap to get those flavorful low-temp dabs. When dabbing, you add a small amount of concentrate to a hot nail and inhale the vapor through a dab rig’s mouthpiece. One of the most common ways to consume shatter is though dabbing with a dab rig. Shatter can be consumed in a variety of ways. The only thing left to do now is smoke it! You may need more than one razor to scrape up your full-extract cannabis oil, as they can become hopelessly sticky.Īnd that, in a word, is how to make THC wax. Scrape and storeįinally, use a razor blade to scrape the potent concentrates off the bottom of the container and place it on parchment paper to cool. It is important to have a gauge that shows you the temperature inside the chamber to avoid burning off the oil.”Īfter the vacuum purge operation, you will have removed almost all traces of butane from your cannabis oil, leaving you with a pure, flavorsome product. The BHO is placed in a thin layer on a glass dish inside the chamber, and the air and butane are sucked out through the pump. We do this using a 3 cfm one-stage vac pump (don’t waste your time with two-stage units). “We vacuum purge all concentrates to remove the remaining traces of liquid butane. This can be done using a pressurized vac pump, and our grower’s process goes like this. Purge remaining butaneĪt this point, you’re left with a thick, amber shatter with trace amounts of butane, and many feel that the solvent must be further purged before consumption. You’ll know the process is finished when the shatter stops bubbling. It’s important to make sure you boil all the solvent away when you make shatter – otherwise you could end up smoking a product still tainted by butane, and that’s bad for your lungs, not to mention potentially explosive. This gradually removes the butane, leaving you with true shatter. Now place the Pyrex container in the top portion of the boiler and let the liquid evaporate. Make sure it’s electric: Use a gas stove and you’re liable to start a fire. Fill your double boiler and put it on a hot electric range. The next step in making shatter can also be rather dangerous. Even a hidden pilot light could spark an explosion, and you definitely don’t want that. This part is absolutely essential: Spray the butane outdoors, with ample ventilation, as far as possible from any buildings, vehicles, or other potential sources of ignition. If you want to know how to make marijuana wax without destroying your home at the same time, listen up. ![]() A thick green-gray-brown oil should drip from the bottom holes into your Pyrex container. To make your concentrated marijuana, carefully and slowly spray the butane through the top hole until the canister is empty. Store-bought extractors come with a filter, but coffee filters also work for DIY. One end of the extractor should have a small hole, the other a cap with several holes and an internal filter. You don’t want air pockets, but you want the butane to saturate all the marijuana. Be sure the weed is packed tight, but not too tight. These “honey oil” extractors can be purchased at most head shops, but you can also make one yourself. To continue making shatter, fill the extractor with pot. This amount of concentrate you produce will depend on how laden with crystals the buds are some BHO extractors get up to 20% yield. If you pack an ounce into the extractor and spray it with a full 12-ounce canister of butane, you should get roughly 3.5 grams of shatter. With all your required supplies to hand, grind your weed and let it sit for a while. The first step to making shatter at home is to gather your supplies. But BHO can be done in relative safety if thorough caution is used. Making shatter indoors is a terrible idea and stands a decent chance of blowing your house off its foundation. To start, keep in mind that the BHO method tends to be a hazardous process. We are going to walk you through everything you need to know about how to make BHO using butane solvent extraction. There are a number of different methods for extracting the resinous trichomes from cannabis plant matter, but for simplicity’s sake, we’ll stick to the popular “BHO” (butane hash oil) method. ![]() If you have, you know it’s awesome.īut how do you make shatter? If you’ve ever paid the high price for shatter at a dispensary, you might be asking yourself how to make wax from weed at home. If you love weed and haven’t had your head in the sand for the last few years, surely you’ve heard of shatter, also referred to generally as wax or dabs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |